Hyundai HDBT52-A Original Instructions Manual Download Page 7 | Manualshive

Page: 7 / 23

background image

7

BEWARE OF FOOT INJURY BY CUTTING ATTACHMENT

PAY ATTENTION THAT BYSTANDERS ARE NOT INJURED
THROUGH FOREIGN OBJECTS THROWN FROM THE
MACHINE.

BEWARE OF THROWN OBJECTS HIT BY CUTTING
ATTACHMENTS. NEVER USE WITHOUT PROPERLY
MOUNTED BLADE GUARD.
BEWARE OF BLADE THRUST.

KEEP BYSTANDERS AT LEAST 15 M AWAY.

DO NOT USE SAW BLADE.

GUARANTEE SOUND POWER LEVEL

RISK OF HOT SURFACE

DOT NOT EXPOSE TO FIRE

«
...
5
6
7
8
9
...
»

Summary of Contents for HDBT52-A
























Reviews:

No comments

Related manuals for HDBT52-A

Brand: BLACKLINE Pages: 162

Brand: Hurricane Pages: 66

Brand: Poulan Pro Pages: 21

Lithium Ion Triple Play 9880

Brand: Wahl Pages: 16

Brand: F&F Pages: 6

Brand: GreenWorks Pro Pages: 44

Brand: Mi-Heat Heizsysteme Pages: 4

Brand: Batavia Pages: 16

Garden Groom "Midi" GG10

Brand: Garden Groom Pages: 10

Decora Mural MCM06-1

Brand: Leviton Pages: 2

UltraPower 60V ST60L03

Brand: GreenWorks Pro Pages: 32

Brand: HENX Pages: 33

Brand: ALDI Pages: 29

Brand: ALDI Pages: 34

Brand: ALDI Pages: 40

Brand: Bushranger Pages: 16

Brand: Bushranger Pages: 16

Brand: Bushranger Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands