background image

6

Residual risks

Even if you use this product in accordance with all safety requirements, the potential risk of injury and
damage remains. The following hazards may arise:
- There are harmful health consequences resulting from the emission of vibrations if the product is used

for long periods of time or not managed adequately and properly maintained. The vibrations can produce
the so-called “white finger” disease. If any of the symptoms of "white finger" syndrome appear, see a
doctor immediately. Symptoms of the "white finger" include: numbness, loss of sensitivity, tickling,
tingling, pain, loss of strength, colour changes, or skin condition. These symptoms usually appear on the
fingers, hands or wrists. The risk increases at low temperatures. To reduce this risk, please wear gloves
and keep your hands warm. Limit the operating time.

- There is a risk of hearing loss during prolonged use, in particular if you do not wear hearing protection.

Always wear hearing protection and limit the operating time.

- Cuts if no suitable protective clothing is worn.

-

Inhalation of particles and exhaust gases if a mask of protection is not worn.

-

Contact with projected objects.

-

Burns when touching with hot surfaces.

Intended use

This machine can be used as a trimmer with the cutting edge, and as a brushcutter with the cutting blade.
The grass trimmer must be strictly and only to cut grass or weeds that are not too dense. The brush cutter must be
used to cut hard grass, more dense weeds and small branches with a maximum diameter of 10mm.
This machine is not intended to cut bushes or others similar plants requiring the tool to get off the ground. Do not use
this tool to work other materials such as stones, clay soils, etc.

Symbols

This graphic accompanied by the words WARNING and
DANGER calls attention to an act of a condition which can lead to
SERIOUS INJURY.

READ & UNDERSTAND Operator’s Manual and Safety Manual

ALWAYS WEAR EYE PROTECTION, EAR PROTECTION AND
HEAD PROTECTION.

WEAR FOOT PROTECTION
WEAR GLOVES

Summary of Contents for HDBT52-A
























Reviews: