background image

12

CUTTING WITH A NYLON HEAD

TRIMMING:

This is feeding the trimmer carefully into the material

you wish to cut. Tilt the head slowly to direct debris

away from you. If cutting up to a barrier such as fence,

wall or tree, approach from an angle where any debris

ricocheting off the barrier will fly away from you, Move

the line head slowly until the grass is cut right up the

barrier, but do not jam (overfeed) the line into the

barrier. If trimming up to a wire mesh or chain linked

fence be careful to feed only up to wire. If you go to far

the line will snap off around the wire. Trimming can be

done to cut through weed stems one at a time. Place the

trimmer line head near the bottom of the weed-never

high up which could cause the weed to chatter and catch

the line. Rather than cut the weed right through, just use

the very end of the line to wear through the stem slowly.

WARNING

!

DANGER

Do not to use a steel blade for edging or scalping.

SCALPING AND ENGING:

Both of these are done with the line head tilted at a steep

angle Scalping is removing top growth leaving the earth

bear.

Edging is trimming the grass back where it has spread

over a sidewalk or drive way. During both edging and

scalping, hold the unit a steep angle and in a position

where the debris, and any dislodging dirt and stones,

will not come back towards you even if it ricochets off

the hard surface.Although the picture shows how to

edge and scalp every operator must find for himself the

angles which suits his body size and cutting situation.

WARNING

!

DANGER

Do not trim in any area where there are strands of

fencing wire. Wear protective safety protecting , Do not

cut where you cannot see what the cutting device is

cutting.

Summary of Contents for HDBT32




























Reviews: