background image

1

FEATURES OF YOUR HYUNDAI

67

1

FEATURES OF YOUR HYUNDAI

67

B260N01MC-AAT

Malfunction Indicator Light

This light illuminates when there is a
malfunction of an exhaust gas related
component and the system is not func-
tioning properly. This light will also illumi-
nate when the ignition key is turned to the
"ON"  position, and will go out in a few
seconds  after the engine is started. If it
illuminates while driving, or does not illumi-
nate when the ignition key is turned to the
"ON" position, take your car to your nearest
authorized Hyundai dealer and have the
system checked.

!

CAUTION:

Prolonged driving with the Emission
Control System Malfunction Indicator
Light illuminated may cause damage to
the emission control systems which
could effect drivability or fuel economy.
If the Emission Control System Malfunc-
tion Indicator Light begins to flash ON
and OFF, potential catalytic converter
damage is possible which could result in
loss of engine power. Have the Engine
Control System inspected as soon as
possible by an authorized Hyundai
dealer.

The driver's seat belt warning light and
chime will activate to the following table
when the ignition switch is in "ON" posi-
tion.

B265E01MC-AAT

Seat Belt Warning Light

and Chime

*1) Warning pattern repeats 11 times with

an interval of 24 seconds. If the driver's
seat belt is buckled, the light will stop
within 6 seconds and chime will stop
immediately.

*2) The light will stop within 6 seconds

and chime will stop immediately.

Conditions

Warning Pattern

Seat Belt

Vehicle Speed Light-Blink Chime-Sound

Unbuckled

Buckled

Buckled 

 Unbuckled

Unbuckled

Above 6mph

(10 km/h)

Below 3mph

(5 km/h)

6 seconds

6 seconds

6 seconds *1)

Stop *2)

6 seconds

None

B290A02MC-AAT

Engine Coolant Temperature

Warning Light

WARNING:

Never remove the radiator cap when the
engine is hot. The engine coolant is un-
der pressure and could erupt and cause
severe burns. Wait until the engine is
cool before removing the radiator cap.

!

This warning light shows the temperature
of the engine coolant when the ignition
switch is ON. The warning light illumi-
nates if the temperature of the engine
coolant is above 253.4±5.4°F (123±3°C).
If the warning light illuminates, pull over
and stop as soon as possible and turn off
the engine. Then open the hood and
check the coolant level (See "If the en-
gine overheats" on the page 3-4.) and the
water pump drive belt. If you suspect
cooling system trouble, have your cool-
ing system checked by a Hyundai dealer
as soon as possible.

NOTE:

If the engine coolant temperature warn-
ing light illuminates, it indicates over-
heating that may damage the engine.

Summary of Contents for 2009 Accent











































































































































































































































































Reviews: