HYTECON HYPRO WATER User Manual Download | Manualshive

Page: 11 / 52

background image

11

HYPRO WATER – 05.2021

11

3.

Installation

3.1

Requirements applicable to the
installation site

– The installation site must be clean and

dry.

– A suitable socket must be available at

the installation site. The socket must
have been installed and set up by
a qualified electrician. The electrical
connections must comply with the local
regulations. The mains voltage must
concur with the voltage specifications
on the data plate.

➡

“2.4 Technical data” (page 10).

– Installation above the worktop requires

a suitable recess in or behind the
worktop through which the mains cable
and hoses are routed.

– If the wall bracket is used: Select the

installation site such that 10 cm remains
clear beneath the device for mounting
on the wall bracket.

– Select the installation site such that 20

cm remains clear above the device to
facilitate a filter change.

– If the device is used with the HYPRO

app: A WLAN connection to the
internet must be available at the
installation site.

– If a boiler is used, this must have been

professionally installed.

– The tap at the installation site must

have been professionally installed.

Examples:
a  3-way tap
b  2-way tap
c  Supplementary tap

3.1 / 1

a

b

c

y

Observe the documentation for your
water tap.

Water tap documentation.

«
...
9
10
11
12
13
...
»

Summary of Contents for HYPRO WATER





















































Reviews:

No comments

Related manuals for HYPRO WATER

Hydro-Guard HG-3

Brand: Mueller Pages: 7

Brand: esotec Pages: 32

Brand: tom logisch Pages: 96

TurboTAC Compact

Brand: Next Pages: 3

Brand: EGT Pages: 16

Brand: Eaton Pages: 9

Brand: Crystal Quest Pages: 19

Brand: 3P Technik Pages: 2

Brand: Velcon Pages: 2

Brand: velda Pages: 12

Brand: Zodiac Pages: 12

Brand: Raypak Pages: 20

FIRE–BALL 300 Air Motor Muffler Kit

Brand: Graco Pages: 4

Brand: Graco Pages: 16

Brand: sylber Pages: 36

Brand: Alemlube Pages: 10

Brand: AQUALEAD Pages: 12

Brand: My Water Filter Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands