background image

Fork Tip Alignment

Length of Forks

3% Dimension

0914 mm  (36 in.)
1067 mm  (42 in.)
1220 mm  (48 in.)
1371 mm  (54 in.)
1524 mm  (60 in.)

27.00 mm  (1.10 in.)
32.00 mm  (1.26 in.)
37.00 mm  (1.46 in.)
40.00 mm  (1.57 in.)
46.00 mm  (1.81 in.)

1. TIP ALIGNMENT (MUST BE WITHIN 3% OF

FORK LENGTH)

2. CRACKS

3. LATCH DAMAGE

4. THICKNESS OF BOTTOM OF FORK (MUST BE

90% OF DIMENSION X)

5. FORK BLADE (BOTTOM OF FORK)

6. FORK TOOL 3020387

Figure 10. Check the Forks

6. 

Check  for  any  damaged  or  broken  parts  that
are used to keep the forks locked in position.

7. 

Check that the lift chains are correctly lubrica-
ted.

8. 

Inspect the lift chains for cracks or broken links
and pins.

9. 

Inspect  the  chain  anchors  and  pins  for  cracks
and damage.

10. 

Make  sure  the  lift  chains  are  adjusted  so  they
have equal tension. If the chains need to be re-
placed  or  adjusted,  service  must  be  performed
by authorized personnel.

Control Handle

Check  that  the  steering  operates  smoothly  and
gives good steering control. Move the control handle
to  the  operating  position  and  move  the  handle  to
the left or right to steer the lift truck.

Hydraulic System

  WARNING 

Always  wear  the  proper  protective  equipment  in-
cluding  eye  protection  and  petroleum-resistant
gloves  when  handling  hydraulic  oil.  Thoroughly
wash oil from exposed skin as soon as possible.

Maintenance Procedures Every 8 Hours or Daily

8000 SRM 1379

16

Summary of Contents for B495


























Reviews: