background image

SAFETY PRECAUTIONS

MAINTENANCE AND REPAIR

The Service Manuals are updated on a regular basis, but may not reflect recent design changes to the product. Upda-
ted technical service information may be available from your local authorized Hyster

®

 dealer. Service Manuals pro-

vide general guidelines for maintenance and service and are intended for use by trained and experienced technicians.

Failure to properly maintain equipment or to follow instructions contained in the Service Manual could result in dam-

age to the products, personal injury, property damage or death.

When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened, and that the load being

lifted is balanced. Make sure the crane, cables, and chains have the capacity to support the weight of the load.

Do not lift heavy parts by hand, use a lifting mechanism.

Wear safety glasses.

DISCONNECT THE BATTERY CONNECTOR before doing any maintenance or repair on electric lift trucks. Dis-

connect the battery ground cable on internal combustion lift trucks.

Always use correct blocks to prevent the unit from rolling or falling. See HOW TO PUT THE LIFT TRUCK ON

BLOCKS in the 

Operating Manual

 or the 

Periodic Maintenance

 section.

Keep the unit clean and the working area clean and orderly.

Use the correct tools for the job.

Keep the tools clean and in good condition.

Always use 

HYSTER APPROVED

 parts when making repairs. Replacement parts must meet or exceed the specifi-

cations of the original equipment manufacturer.

Make sure all nuts, bolts, snap rings, and other fastening devices are removed before using force to remove parts.

Always fasten a DO NOT OPERATE tag to the controls of the unit when making repairs, or if the unit needs repairs.

Be sure to follow the 

WARNING

 and 

CAUTION

 notes in the instructions.

Gasoline, Liquid Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Diesel fuel are flammable. Be sure to

follow the necessary safety precautions when handling these fuels and when working on these fuel systems.

Batteries generate flammable gas when they are being charged. Keep fire and sparks away from the area. Make sure

the area is well ventilated.

NOTE:  

The following symbols and words indicate safety information in this manual:

  WARNING 

Indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

  CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury and property damage.

On  the  lift  truck,  the  WARNING  symbol  and  word  are  on  orange  back-

ground. The CAUTION symbol and word are on yellow background.

Summary of Contents for B257



























Reviews: