manualshive.com logo in svg

Hyper Rip Rail, Owner'S Manual

Share
Download
Hyper Rip Rail Owner'S Manual Download Page 23

P

A

G

E

21

A

D

JU

S

T

M

E

N

T

BMX Scooter

ASSEMBLY 

The following sections describe final brake system adjustments 
required before riding.

1. Align and tighten brake shoes:

If the top and bottom edges are not evenly aligned to rim then 
first loosen the brake shoe nuts until brake shoes move freely. 
Align the brake shoes top and bottom edges evenly to the rim as 
shown. Then tighten bolts, but never over tighten.

2. Put the brake shoes the correct distance from the rim:

Correct position of each brake shoe is 1/16 inch away from the 
rim. If brake shoe distance is off first try turning the rotor 
adjusting barrels in or out to make the adjustment. NOTE: You 
may need to loosen or tighten locknut’s before and after turning 
adjusting barrels.

3. Adjust Cable:

If the brake shoes cannot be positioned to correct distance from 
the rim hold both brake shoes against the rim and loosen the 
cable anchor bolt. Position each brake shoe 1/16 inch away from 
the rim. Pull brake cable tight getting rid of any excess slack. Be 
careful not to pull brake arm out of center. Tighten anchor bolt 
securely. Squeeze the brake lever to check brake action.

3

ADJUSTING

BARREL 

LOCKNUT 

CABLE ADJUSTER

LEVER ADJUSTING BARREL

ADJUSTING

BARREL 

2

1

Summary of Contents for Rip Rail





































Reviews:

No comments

Brands by name

Popular brands

Load more brands