HYOSUNG TE450 - Service Manual Download | Manualshive

Page: 211 / 262

background image

CHASSIS 7-58

2. Tension damping force

To adjust the tension damping force turn in the
adjuster

②

fully for “S” or “H” direction (counter-

clockwise or clockwise).
Count  the  number  of  turns  from  the  fully  turned-in
position.
Fully  turned-in  “H”  direction  (or  clockwise)  provides
stiffest  tension  damping  force  and  turning  “S”  direc-
tion  (or  counter-clockwise)  the  adjuster  will  soften
tension damping force.

STANDARD REAR SHOCK ABSORBER DAMPING FORCE

Compression

Tension

Softer

Standard

Stiffer

Turn to “S” direction (counter-clockwise)

1

½

turn from end of “S” direction (counter-clockwise)

Turn to “H” direction (clockwise)

Turn to “S” direction (counter-clockwise)

1

½

turn from end of “S” direction (counter-clockwise)

Turn to “H” direction (clockwise)

▣

▣

DAMPING FORCE ADJUSTMENT

The compression and tension damping force are
adjustable for rider’s preference, rider’s weight and
field condition.

1. Compression damping force

To adjust the compression damping force turn in the
adjuster

①

fully for “S” or “H” direction (counter-

clockwise or clockwise).
Count  the  number  of  turns  from  the  fully  turned-in
position.
Fully  turned-in  “H”  direction  (or  clockwise)  provides
stiffest  compression  damping  force  and  turning  “S”
direction (or counter-clockwise) the adjuster will soft-
en compression damping force.

NOTE

Do not turn the adjuster screws more than given
position, or the adjuster may be damaged.

①

②

Rear shock absorber

tension damping force

adjuster

Standard

1

½

turn from end of “S”

direction (counter-clockwise)

Rear shock absorber

compression damping

force adjuster

Standard

1

½

turn from end of “S”

direction (counter-clockwise)

COPYRIGHTED

«
...
209
210
211
212
213
...
»

Summary of Contents for TE450 -







































































































































































































































































Reviews:

No comments

Related manuals for TE450 -

Brand: N-Com Pages: 28

Brand: R&G Pages: 8

Brand: Happy Trails Pages: 3

Brand: Suzuki Pages: 151

Brand: kellermann Pages: 2

Brand: BMW Motorrad Pages: 146

SPORTCITY CUBE 125

Brand: APRILIA Pages: 157

Brand: AGV Pages: 45

690 Enduro R 2019

Brand: KTM Pages: 274

Brand: Zontes Pages: 119

Brand: IRC Pages: 2

Brand: HERO Pages: 68

Brand: X-lite Pages: 33

Brand: Honda Pages: 130

Brand: hepco & becker Pages: 4

Brand: DYNATEK Pages: 8

Brand: SPmoto Pages: 92

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands