manualshive.com logo in svg

HYOSUNG NH-2700, Operator'S Manual

Share
Download
HYOSUNG NH-2700 Operator'S Manual Download Page 52

NH-2700                                                                                                                  4. Operating Instructions   

4 - 29 

 

2) Turn the pulley located in left upper in order to 

move jammed note into a well removed 
position. 

 

 

 

 

3) Take out the jammed note carefully. 
 

 

 

 

 

4)  Remove  the  cash  cassettes  to  check  whether 

there is any jammed note inside of CDU body. 
If so, remove the jammed note from it. 

[WARNING!]

 

If the belt is detached from the Roller, the 
lifespan of the belt can be dramatically 
reduced which can result in breakage. 
Therefore, it is extremely important to check if 
the belt is positioned correctly after removing 
the jammed bills. 

 

Summary of Contents for NH-2700


















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands