HYOSUNG NH-2700 Operator'S Manual Download Page 106

Page: 106 / 337

NH-2700 5. Operator Function

5- 46

5.6.6.2 FLICKER

This

FLICKER

contains

ALL FLICKER SENSOR, EPP FLICKER, CDU FLICKER, SPR FLICKER

and

MCU FLIKCER

. Please press each button on this menu to change test mode ON, OFF or

FLICKING. To go back to the previous screen, press the

CANCEL

key in pinpad.

Accessing the SENSOR

1) Select

DIAGNOSTICS

in the OPERATOR FUNCTION.

2) Select

AUXILIARY UNIT

in the DIAGNOSTICS menu and then select

FLICKER

in the

AUXILIARY

menu.

3) Select any button to test EPP, CDU, SPR, MCU in each or ALL FLICKER..

5.6.7 AGING

The AGING function is only used at the factory.

Accessing the AGING

1) Select

DIAGNOSTICS

in the OPERATOR FUNCTION.

2) Select

AGING

in the

DIAGNOSTICS

menu.

3) All units will be tested unlimitedly. When you press

CANCEL

key, the testing will be stopped.

Summary of Contents for NH-2700

















































































































































































































































































































































Search results

Summary of Contents for NH-2700

Reviews:

Brands by name

Popular brands

HYOSUNG NH-2700, Operator'S Manual

Search results

Summary of Contents for NH-2700

Reviews:

Brands by name

Popular brands