Hydromatic S12L Series, Installation And Service Manual, Page: 10 / 16

10
A1 65-006-1 BEARING – BALL (UPPER) R 1
A2 65-023-1 BEARING – BALL (LOWER) R 1
A3 150-019-1 O-RING 1
A4 150-032-1 O-RING SC 1
A5 150-038-1 O-RING SCI 2
A6 150-057-1 O-RING SCI 1
A7 150-108-1 O-RING (VITON) SC 1
A8 239-035-1 SCREW – HHC 1/2-13 x 5-1/4 4
A9 239-038-1 SCREW – HHC 1/2-13 x 7-1/4 12
A10 556-007-1 SCREW – CAP (HEX SOC.) 6
A11 557-000-1 CONNECTOR – WIRE 3
A12 975-010-1 RING – RETAINING 1
A13 975-014-1 RING – RETAINING 1
A14 1272-001-3 TUBING – NYLON 1
A15 1664-008-1 PLUG – PIPE 3/8 SKT HD BRASS 3
A16 2310-004-3 SLEEVE – SHAFT SC 1
A17 2855-001-1 KEY – SQUARE 3/8 1
A18 2921-001-1 SCREW – CAP (FL. HD SOC) 4
A19 4580-001-1 SCREW – DRIVE 4
A20 6000-011-1 WIRE w/TERMINAL 14 GA. RED 1
A21 6579-002-1 KEY – SQUARE 1/4 1
A22 7398-000-2 HOUSING – SEAL 1
A23 7400-004-2 HOUSING – MOTOR 1
A24 7401-100-2 HOUSING – BEARING 1
A25 8206-000-1 PLATE – INSTR (DRAIN) 1
A26 8206-001-1 PLATE – INSTR (FILL & DRAIN) 1
A27 8354-000-3 RING – RETAINING STATOR 1
A28 8472-002-5 SEAL FAILURE ASS'Y 1
A29 9176-000-1 SLEEVE – WIRE 6
A30 11065-002-3 SCREEN 3.81 DIA. 1
A31 12672A002 CONNECTOR – BUTT 3
A32 13425-023-1 NAMEPLATE 1
Ref. Part Part
No. No. Description Qty.
A33 19101A017 SCREW – CAP HEX SST 3/8 6
A34 19103A052 SCREW – CAP HEX SST 1/2 6
A35 24709110000 OIL – TRANSFORMER 10.5
A36 13424-004-1 LABEL – HEAT SENSOR 1
C1 3718-000-1 SEAL Carbon Ceramic / Buna-n S 1
C2 3718-000-1 SEAL Carbon Ceramic / Buna-n S 1
C2 3718-001-1 SEAL Tungsten Carbide / Buna-n C Optional
F1 19109A080 NUT – HEX SST 3/4 4
F2 15175-300-1 BAIL – LIFTING 1
F3 05454A030 WASHER – LOCK 3/4 4
F4 05454A027 WASHER – LOCK 5/8 2
F5 15174-000-1 BRACKET – MOUNTING 2
F6 19105A033 SCREW – CAP HEX SST 5/8 2
51700-068-7 Seal Kit S
51700-368-7 Carbide Seal Kit C
-24709110000 Paraffinic Oil O
ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur nished
as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1)
pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller),
(6) quan ti ty required, and (7) shipping instructions.
Ref. Part Part
No. No. Description Qty.
Ref. Part Part
No. No. Description Qty.
Motor End
Parts List
Notes: S — Parts in Seal Kit C — Parts in Carbide Seal Kit I — Parts in Impeller Kit R — Parts in Rebuild Kit *Consult Factory
O — Amount of oil required will vary between 8-10.5 gal. depending on stator size, fill to above motor windings.
Wet End
Parts List
Item# Description S4T S8L S12L S8LA
Qty. Qty. Qty.
D1 SCREW – MACH. FL. HD. 829-009-1 (4) 07597A021 (4) --- 07597A021 (4)
D2 WASHER – IMPELLER 1945-001-3 1945-001-3 1945-001-3 1945-001-3
D3 SCREW – CAP (HEX SOC.) 3/4 3879-002-1 3879-002-1 3879-002-1 3879-002-1
D4 VOLUTE 13688-000-2 7394-200-2 25457F200 7394-000-2
D5 RING – WEAR 13695-000-3 8345-000-2 24548D000 13535-000-3
D6 CLAMP – WEAR RING --- --- --- 13536-000-3
D7 BELL – SUCTION --- --- 10587-100-2 ---
D8 STAND – PUMP --- --- 10627-000-5 ---
D9 SCREW – CAP HEX SST 1/2-13 --- --- 19106A017 ---
D10 SCREW – CAP HEX SST 1/2-13 --- --- 06106A019 (3) ---
D11 SCREW – CAP SKT HD 1/4-20 --- --- 19103A052 (8) ---
For use with product built with USEM motor.
For use with product built with USEM motor.