background image

 8

www.hydrofarm.com

AADHC180P_instrux_12.2014

www.hydrofarm.com

TROUBLE SHOOTING

Please try the following solutions before requesting after-sale service.

TROUBLE

CAUSE

SOLUTION

Machine does not run

Unit is not plugged in.

Plug in the unit.

Ambient temperature is under 5 

degrees or above 35 degrees.

To protect the machine, use it only when ambient 

temperature is between 5 and 35 degrees.

The humidity sensor is loose, wet or 

defective; the screen will show “E5”.

Check the sensor connection. Use a blower to dry the 

humidity sensor behind the front cover. If the machine still 

does not run, contact your retailer to replace the sensor.

The temperature sensor is loose or 

defective; the screen will show “E6”.

Check the sensor connection. Contact your retailer to replace 

the sensor.

Machine runs but does 

not dehumidify

The humidity set point is higher 

than the ambient humidity.

Reset the humidity to a lower set point, or power off the 

machine if the desired humidity level has been reached.

Reduced dehumidifier 

capacity

Filter mesh is jammed.

Clean the filter mesh according to manual.

Air-in and/or Air-out louvers are 

jammed.

Clear the blockage from Air-in and/or Air-out louvers.

No air inlet

Filter mesh or Air-in louver is 

jammed.

Clean filter according to instructions or clean the louver 

blockage.

Loud Operation

Machine is situated on an incline or 

decline slope.

Move to a level location.

Filter mesh is jammed.

Clean filter mesh according to instructions.

WARRANTY

Hydrofarm warrants the dehumidifier to be free from defects in materials and workmanship. The 

warranty term is one year beginning on the date of purchase. Misuse, abuse, or failure to follow 

instructions is not covered under this warranty. Hydrofarm will, at our discretion, repair or replace 

the unit covered under this warranty if it is returned to the original place of purchase. To request 

warranty service, please return the dehumidifier, with original sales receipt and packaging, to your 

place of purchase. The purchase date is based on your original sales receipt.

INSTRUCTION MANUAL

Summary of Contents for AADHC180P









Reviews: