Hydro-Gear HGM-C Service And Repair Manual Download Page 17 | Manualshive

Page: 17 / 24

background image

HGM-C LSHT Wheel Motor

15

Distributor Plate (14)

Indentations

Slots

O-ring (18)

O-ring (16)

Port Surface

Housing (9)

Gearwheel (17)

GEARWHEEL SET

DISTRIBUTOR PLATE

Figure 13, Distributor Plate

Figure 14, Gearwheel Set/O-ring

Assembly

1. Mount seal (5), washer (4), and ball bearing

(3) onto output shaft (7).

See page 11.

2. Install check valves (11), needle bearing

(12), output shaft assembly, retaining ring

(2), and O-ring (13).

See pages 12 - 14.

3. Turn the distributor plate (14) so that the

slots are against the motor housing (9) and

indentation in the distributor plate is pointing

to port surface.

See figure 13.

Assembly

1. Mount seal (5), washer (4), and ball bearing

(3) onto output shaft (7).

See page 11.

2. Install check valves (11), needle bearing

(12), output shaft assembly, retaining ring

(2), O-ring (13), and distributor plate (14).

See pages 12 - 15.

3. Place

new

O-rings (16, 18) in the O-

ring grooves of the gearwheel set (17).

See figure 14.

«
...
15
16
17
18
19
...
»

Summary of Contents for HGM-C

























Reviews:

No comments

Related manuals for HGM-C

Brand: jcb Pages: 122

Brand: Quick Fuel Technology Pages: 5

Brand: Suzuki Pages: 91

Brand: Central Machinery Pages: 30

Brand: Leadshine Technology Pages: 55

Brand: O.S. engine Pages: 17

Brand: O.S. engine Pages: 20

Brand: O.S. engine Pages: 18

Revenge CTM Series

Brand: Absima Pages: 3

Brand: O'Donnell Pages: 16

MAX-32SX-H Series

Brand: O.S. engine Pages: 32

Brand: Honda Pages: 48

Brand: ST Pages: 281

Brand: Wood-mizer Pages: 146

Brand: Desert Aircraft Pages: 9

Brand: KTM Pages: 28

Brand: Seidel Pages: 17

Brand: Seidel Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands