Page 4
7.
Programming the operator
(
Note:
The operator will exit programming if left for 30 seconds.)
(Programming cont.)
Preparation
With the Carriage Release Lever horizontal,
move the door by hand until the Carriage engages
with the Shuttle.
Turn on the power, the Lamp comes on while the
Display runs from ‘99’ to ‘11’.
99
99
99
99
11
11
11
11
The Display changes to ‘--‘. Standby Mode.
--
--
--
--
Setting Open and Close Positions
Press and hold the
SET
button, until ‘P1’ is
displayed.
P1
P1
P1
P1
Press
SET
again, ‘OP’ is displayed.
OP
OP
OP
OP
Press and hold the
UP
button. While opening,
‘OP’ flashes.
OP
OP
OP
OP
Release the
UP
button when the open position is
reached.
Use the UP or DOWN buttons to adjust the open
position.
Press
SET
, and ‘CL’ is displayed.
CL
CL
CL
CL
Press and hold the
DOWN
button. While closing,
‘CL’ flashes.
CL
CL
CL
CL
Use the UP or DOWN buttons to adjust the
closed position.
Press
SET
, and the door will open and close
automatically to establish normal force
requirements. Finally ‘--’ is displayed.
OP
OP
OP
OP
CL
CL
CL
CL
--
--
--
--
Adding eKey Remotes
Press the
CODE
button. ‘Su’ is displayed.
Su
Su
Su
Su
Choose and press a button on the eKey Remote.
Su
Su
Su
Su
Press the same button again to confirm.
‘SU’ flashes and then ‘--’ is displayed.
(
Su
Su
Su
Su
)
--
--
--
--
Repeat the above steps for additional eKey
Remotes. A maximum of 20 may be stored. An
attempt to add another will display ‘Fu’.
Fu
Fu
Fu
Fu
Deleting Remotes
Caution
: This function deletes all remotes
Press and hold the CODE button for 8 seconds.
‘dL’ is displayed
dL
dL
dL
dL
Operating Force Adjustment
Press and hold the
SET
button, until ‘P1’ is
displayed.
P1
P1
P1
P1
Press the
UP
button once. ‘P2’ is displayed.
P2
P2
P2
P2
Press
SET
again. The current force setting is
displayed. Press
UP
or
DOWN
to increase or
decrease this value by one step at a time.
Maximum is ‘F9’; Minimum is ‘F1’. Press SET
to confirm.
F9
F9
F9
F9
F1
F1
F1
F1
Default setting is ‘F5’
F5
F5
F5
F5
Safety Beam – Enabling and Disabling
Press and hold the
SET
button, until ‘P1’ is
displayed.
P1
P1
P1
P1
Press the
UP
button twice. ‘P3’ is displayed.
P3
P3
P3
P3
Press the
SET
button to show the beam Status.
‘H0’ means Disabled, ‘H1’ means Enabled.
H0
H0
H0
H0
H1
H1
H1
H1
Press the
UP
button to Enable. ‘H1’ is displayed.
H1
H1
H1
H1
Press the
DOWN
button to Disable. ‘H0’ is
displayed.
H0
H0
H0
H0
Press the
SET
button to confirm and exit.
NOTE:
If Safety Beams are
not
fitted, ensure the
above function is Disabled, or the operator will
open, but will
not
close.
H0
H0
H0
H0
Auto-close
Press and hold the
SET
button, until ‘P1’ is
displayed.
P1
P1
P1
P1
Press the
UP
button three times. ‘P4’ is displayed.
P4
P4
P4
P4
Press the
SET
button to show the Auto-close
Status.
‘b0’ means ‘No Auto-close’, ‘b9’ is maximum
Auto-close.
b0
b0
b0
b0
b9
b9
b9
b9
Press the
UP
button to increase, or the DOWN button to
decrease the delay by 1 minute.
Press the
SET
button to confirm and exit.
8.
Owner’s Guide
Notes and Warnings:
Only operate the door when it is in full view.
Do not allow young children to play with the controls.
Keep people, pets and property clear of the moving door.
The door operator is intended for indoor installation.
The door and operator should be serviced annually.
Trouble Shooting
In the event of a malfunction, to judge where the fault may lie, use the manual over-ride and test the door by hand, and check if the
operator will function with the door disengaged.
Problem
Possible Cause
Remedy
Noisy Chain
Chain has become loose
Adjust the M8 Nut on the spring
No response from the motor
Mains supply/loose plug, blown
fuse
Check the mains.
Check/replace the fuse with the same type
Door opens but will not close
Safety Beam (if fitted) is faulty
Test by disabling the beam (see programming)
The motor works from the push button,
but not the remote
Remote faulty or battery low
Replace remote battery. If two or more remotes fail,
replace the control board.
Remote range is short
Remote battery low
Replace remote battery
Door fails to close fully and re-opens,
or door fails to open fully
Operating Force too low
Test the door by hand. Slightly increase the
Operating Force (see Programming)
