background image

Table of Contents

HYDAC FILTER SYSTEMS GMBH

ii

BeWa OFU 3120755d en-us lq

Table of Contents

1

General .....................................................................................................................  5

1.1

Imprint ..............................................................................................................  5

1.2

Documentation Representative........................................................................  5

1.3

Purpose of this manual ....................................................................................  6

1.4

Target group of the manual..............................................................................  6

1.5

Illustrations in the manual ................................................................................  7

1.5.1

Illustration on the title page..................................................................  7

1.5.2

Representation of requirements ..........................................................  8

1.5.3

Representation of procedural instructions ...........................................  8

1.5.4

Representation of intermediate results/results ....................................  9

1.5.5

Representation of warning/general safety information ......................  10

1.5.6

Signal words and their meaning in the general safety information ....  11

1.6

Hazard symbols / pictograms.........................................................................  12

1.7

Supplementary symbols.................................................................................  13

1.8

Exclusion of liability/warranty .........................................................................  14

1.9

Notes on copyright .........................................................................................  14

1.10 Validity of this manual ....................................................................................  15

2

Safety information ...................................................................................................  16

2.1

Fire-fighting / extinguishing a fire ...................................................................  17

2.2

Stoppage in an emergency (EMERGENCY STOP).......................................  18

2.3

Observing regulatory information ...................................................................  18

2.4

Wear suitable clothing....................................................................................  18

3

Overview of the filtration unit...................................................................................  19

3.1

Proper/designated use ...................................................................................  20

3.2

Improper use or use deviating from intended use..........................................  21

3.3

Checking the scope of delivery ......................................................................  22

3.4

Dimensions ....................................................................................................  24

3.4.1

OFU - Dimensions .............................................................................  25

3.5

Hydraulic diagram ..........................................................................................  26

Summary of Contents for OFU Filtromat









































































Reviews: