Hyco Zen Solo Series Product Instruction Manual Download Page 2

Overview

Thank you for purchasing a Zen Solo 100°C instant boiling water tap. It replaces the need 

for a traditional kettle in the home, or counter/ wall mounted boiling water unit in the 

office. 

The Zen Solo can be installed over a sink or with the stylish, tempered glass design Zen 

Font.

Key Features

• 

Energy efficient boiling water tank.

• 

Safety lock and cool touch spout. 

• 

360° swivel spout.

• 

Pattern recognition technology to learn and predict boiling water usage.

• 

Supplied with initial scale filter for the inlet to the boiling tank.

• 

Two temperature settings 100°C and 98°C.

• 

Designed and assembled in the UK.

Always switch off the mains electricity before commencing installation.

Only connect the unit to a single-phase supply as specified on the rating plate.

Ensure tank is full of water and tap flushed through before switching power on.

The supply cord cannot be replaced by the user. If the cord is damaged the 

appliance should be returned to the manufacturer or an authorised service agent 

for replacement.

The hoses and pipes supplying this heater must not come into contact with any 

fixed wiring or the supply cord.

Do not carry the appliance by the supply cord.

1. Important Safety Points

Please fully read these instructions before commencing installation and follow to ensure 

that installation and operation are simple and safe.

2

Summary of Contents for Zen Solo Series


























Reviews: