background image

hy-gain

®

 LIMITED WARRANTY 

 

hy-gain

 Warrants to the original owner of this product, if manufactured by 

hy-gain

 and 

purchased from an authorized dealer or directly from 

hy-gain

 to be free from defects in 

material and workmanship for a period of 

12

 months for rotator products and 

24

 months 

for antenna products  from date of purchase provided the following terms of this warranty 
are satisfied. 
 
1.

 

The purchaser must retain the dated proof-of-purchase (bill of sale, canceled check, 
credit card or money order receipt, etc.) describing the product to establish the 
validity of the warranty claim and submit the original or machine reproduction of 
such proof-of-purchase to 

hy-gain

 at the time of warranty service.  

hy-gain

 shall have 

the discretion to deny warranty without dated proof-of-purchase.  Any evidence of 
alteration, erasure, or forgery shall be cause to void any and all warranty terms 
immediately. 

 
2.

 

hy-gain

 agrees to repair or replace at 

hy-gain’s

 option without charge to the original 

owner any defective product under warranty, provided the product is returned postage 
prepaid to 

hy-gain.

 

 
3.

 

Under no circumstances is 

hy-gain

 liable for consequential damages to person or 

property by the use of any 

hy-gain

 products. 

 
4.

 

Out-of-warranty Service:  

hy-gain

 will repair any out-of-warranty product provided 

the unit is shipped prepaid.  All repaired units will be shipped COD to the owner.  
Repair charges will be added to the COD fee unless other arrangements are made. 

 
5.

 

This warranty is given in lieu of any other warranty expressed or implied. 

 
6.

 

hy-gain

 reserves the right to make changes or improvements in design or manufacture 

without incurring any obligation to install such changes upon any of the products 
previously manufactured. 

 
7.

 

All 

hy-gain

 products to be serviced in-warranty or out-of-warranty should be 

addressed to  

hy-gain

,  308

 

Industrial Park Road, Starkville, 

Mississippi 39759, USA

 and must be accompanied by a letter describing the 

problem in detail along with a copy of your dated proof-of-purchase. 

 
8.

 

This warranty gives you specific rights, and you may also have other rights which 
vary from state to state. 

Summary of Contents for LJ-113












Reviews: