background image

2

JIN04MKIIC_V1 10/01/17

Contents

INSTALLATION & COMMISSIONING
CHECKLIST ................ .......... ......................................... 3
TECHNICAL DATA…………………………............................... 5

INSTALLING THE APPLIANCE………………………………. ....... 6

FLUE ARRANGEMENT …………………………………............................................................................8
ADDITIONAL AIR VENTING (GB ONLY) ............. ........................................................................8
OPENING THE STOVE DOOR……………………………………................................................................9
GAS SUPPLY CONNECTIONS........... .................. ......................................................................10
TESTING SUPPLY PRESSURE ........... .................. ......................................................................10

INSTALLATION OF THE FIRE-BED INTO THE
STOVE………….…………………………………………………………. 11

FITTING THE CANOPY – (OPTIONAL)................. ......................................................................14
SPILLAGE MONITORING SYSTEM……………………………… ............................................................14

SERVICING INSTRUCTIONS…………............................... 16

SPARES................................... ......................................................................... 17

Please read these instructions carefully

This appliance is intended for use on a gas installation with a governed

meter.

It is important that your stove is correctly installed as Hunter Stoves Limited cannot accept
responsibility for any fault arising through incorrect installation.

Summary of Contents for HUNTER HAWK 4 MKII


















Reviews: