background image

The Hunter Douglas

®

 Lifetime Guarantee is an expression of our desire to provide a thoroughly satisfying 

experience when selecting, purchasing and living with your window fashion products. If you are not thoroughly 
satisfied, simply contact Hunter Douglas at (888) 501-8364 or visit hunterdouglas.com. In support of this policy  
of consumer satisfaction, we offer our Lifetime Limited Warranty as described below.

NOTE

:

 

In no event shall Hunter Douglas or its licensed fabricators/distributors be liable or responsible for incidental 

or consequential damages or for any other indirect damage, loss, cost or expense. Some states do not allow the exclusion or 
limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty 
gives you specific legal rights, and you may also have other rights which vary from state to state. 

Different warranty periods and terms apply for commercial products and applications.

Hunter Douglas (or its licensed fabricator/distributor) will repair or replace the 

window fashion product or components found to be defective. 

COVERED

BY

 

A

 

LIFETIME

 

LIMITED

 

WARRANTY

•   Hunter Douglas window fashion products are 

covered for defects in materials, workmanship 
or failure to operate for as long as the original 
retail purchaser owns the product (unless shorter 
periods are provided below).

•   All internal mechanisms.
•   Components and brackets.
•   Fabric delamination.
•   Operational cords for a full 7 years from the  

date of purchase.

•   Repairs and/or replacements will be made with 

like or similar parts or products.

•   Hunter Douglas motorization components are 

covered for 5 years from the date of purchase.

NOT

 

COVERED

BY

 

A

 

LIFETIME

 

LIMITED

 

WARRANTY

•   Any conditions caused by normal wear and tear.
•   Abuse, accidents, misuse or alterations to the 

product.

•   Exposure to the elements (sun damage, wind, 

water/moisture) and discoloration or fading  
over time.

•   Failure to follow our instructions with respect  

to measurement, proper installation, cleaning  
or maintenance.

•   Shipping charges, cost of removal and reinstallation.

TO

 

OBTAIN

 

WARRANTY

 

SERVICE

1.  Contact your original dealer (place of purchase) for warranty assistance.
2.   

Visit hunterdouglas.com for additional warranty information, frequently asked questions and access to service locations.

3.   Contact Hunter Douglas at (888) 501-8364 for technical support, certain parts free of charge, for assistance in obtaining

warranty service or for further explanation of our warranty.

LIT888643A

8/18

Summary of Contents for Provenance PowerView Woven Wood Shades





















Reviews: