Hunter H39, Operator'S Manual

Page: 199 / 216

Maintenance
14.5
the specific paint to be used in your area.
Important: Do not paint the zinc anodes (connected to the
boat’s bonding system) on the outside of the transom.
14.2.11.1 Keel Maintenance for Cast Iron (where
applicable)
The cast iron keel (upper section only on some
models) was coated with an epoxy primer before
leaving Hunter Marine. You will find that as with
most items, particularly underwater gear, ongoing
maintenance will probably be required during sea-
sonal or routine haulouts.
The epoxy primer used on your boats Keel or
upper section was manufactured by International
Marine Coatings. The product numbers used are as
Follows:
Intergrade 269 Epoxy Primer / Tie Coating
Color / EGZ088 – Red Base
Converter / Curing Agent – EGA 089
The above products should be applied according
to the manufactures printed instructions. For more
information you may wish to visit their website at
http://www.yachtpaint.com/usa/ or call 800-468-7589
by email to Interluxtechnicalservice@international-
paint.com .
Compatibility of product should be investigated if
other brands or types of Epoxy Coatings are pre-
ferred by the boat owner or repair facility.
14.2.12 PlasDECK
PlasDECK is a plastic product, so it doesn’t require any
of the maintenance demanded by teak and it’s easy to
clean. You never need to apply any protectants, oils, or
other products to preserve the finish. Fish blood, food,
drinks, and dirt are easily washed away. Listed below
are specific instructions for the maintenance of your
PlasDECK.
Power Wash It! A small household power-washer (around
1500 psi) works well to lift debris from the textured sur-
face of PlasDECK.
Soap! Soaps such as boat wash or Simple Green™ can
be used to help release the dirt. Food spills, especially
oily foods, should be cleaned with a safe degreaser such
as dish detergent or Marine Clean™. Bleach can be used
for sterilization if desired.
Because PlasDECK is a PVC, it is susceptible to oil, gas,
diesel, and acetone. If this type of spill occurs, clean
immediately and thoroughly with a soapy detergent such
as dish soap, boat wash, or Simple Green™.
Brush! A nylon brush is often helpful to release stubborn
debris from the surface. If desired, a short bristled wire
brush can be used on wet decking with soap and water
to help loosen particles. IMPORTANT: If you use a wire
brush, always move the brush in the direction of the
grains in the PlasDECK.
Sanding! For bad scuffs, small cigarette burns, or really
stubborn stains that have been left to dry, lightly sand
the area with 40 grit sandpaper. Also, if an area is worn
smooth for some reason, the texture can be restored by
lightly sanding. Make sure you sand in the direction of
the grain with short strokes. Use a heat gun or let the sun
heat your deck over time to blend tones on any areas that
have been lightened during the sanding process. Don’t
use a power sander on your PlasDECK! It will warp the
‘grain’ that lends to PlasDECK’s teak appearance.
Patch it! A patch can be used to repair any serious dam-
age to the deck. Contact PlasDECK for more information
on patching by visiting our website at www.PlasDECK.us
or by calling us directly at 1-800-320-1841.
DON’T bother wearing black-soled shoes on PlasDECK.
Black shoes may leave scuffs on any decking surface.
Wear boat shoes or no shoes. With PlasDECK’s non-skid
surface you won’t have to worry about the surface being
slippery when wet.
DON’T put oil, varnish, paint, sealers or lacquers on your
PlasDECK! Isn’t that why you chose PlasDECK instead
of teak? The PlasDECK doesn’t need protectants and
doesn’t require this maintenance.
OUCH! As with any deck, including teak, don’t place hot
metals or other hot objects on PlasDECK.