Hunter Douglas Luminette PowerGlide 2.1 Page 22 Installation, Operation & Care Manual Download | Manualshive

Page: 22 / 36

background image

INSTALLATION

20

Swivel Plate Attachment

Swivel plates are right- and left-specific, marked by an R or
an L. The swivel plates are packaged with the product’s
hardware.

■

Snap the rivet on the swivel plate into the front
clip on the motor housing. Swivel plates attached
on the left will have

STD L

stamped on the top.

Swivel plates attached on the right will have

STD

R

on the top.

■

Snap the rivet on the other swivel plate onto the swivel arm (side stack) or into the front clip
on the non-control end cap (split stack). Swivel plates attached on the right will have

STD R

stamped on the top. Swivel plates attached on the left will have

STD L

on the top.

STD R

STD L

Rivet

ST

D

L

Swivel Plate

Side Stack

Swivel Arm

Rivet

Swivel Plate

Split Stack

Rivet

Front Clip

Non-Control End Cap

STD

R

STD

R

«
...
20
21
22
23
24
...
»

Summary of Contents for Luminette PowerGlide 2.1





































Reviews:

No comments

Related manuals for Luminette PowerGlide 2.1

Brand: Camtree Pages: 2

Brand: Camtree Pages: 11

Brand: Camtree Pages: 4

Brand: Yolin Pages: 25

Brand: EAL Pages: 4

Brand: Yakima Pages: 11

Brand: Hama Pages: 10

Brand: Napoleon Pages: 4

Brand: Yakima Pages: 8

Brand: YUNEEC Pages: 10

Brand: Stobag Pages: 3

PowerPack TPB-2112

Brand: texet Pages: 16

Brand: Actia Pages: 37

Brand: Montgomery Ward Pages: 4

Brand: GDC Pages: 5

TUFFScreen 8x8 Fungo

Brand: Beacon Athletics Pages: 6

Brand: ORELL Pages: 28

Router Table Spline Jig

Brand: Rockler Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands