manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Installation Manual, Page: 7 / 50

Share
Download
Humminbird MEGA 360 Fortrex Installation Manual Download Page 7

1

Introduction

Introduction

This manual will guide you through the following installation requirements for the 
MEGA 360 Imaging transducer:

•  Installing the Trolling Motor Bracket
•  Connecting to the Control Head and Power
•  Testing the Installation
•  Powering Off

Before proceeding with this installation, the Humminbird control head 
and Minn Kota trolling motor should be installed. The MEGA 360 
Imaging transducer can be connected directly to the control head or to 
a Humminbird Ethernet Switch (optional) for networking. 

Compatibility

Control Heads: 

MEGA 360 Imaging is compatible with SOLIX Series and HELIX 

Series fish finders equipped with MEGA and can be mounted on  
Minn Kota Ultrex, Fortrex, and Maxxum bow-mount trolling motors. 

MEGA 360 Imaging Minn Kota Trolling Motor Humminbird Fish Finder

MEGA 360 Ultrex

Minn Kota Ultrex

SOLIX Series:

 SOLIX G2 models

HELIX Series:

 HELIX MEGA 

G3N models

MEGA 360 Fortrex

Minn Kota Fortrex

Minn Kota Maxxum

SOLIX Series:

 SOLIX G2 models

HELIX Series:

 HELIX MEGA 

G3N models

NOTE:

 You must have a GPS heading sensor (compass) installed in order to use the 

MEGA 360 Imaging navigation features.

Summary of Contents for MEGA 360 Fortrex



















































Reviews:

No comments