manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Installation Manual

Share
Download
Humminbird MEGA 360 Fortrex Installation Manual Download Page 44

38

Troubleshooting

Troubleshooting

Before contacting the Humminbird Technical Support, please read the following 
section. Taking the time to review these troubleshooting guidelines may allow you 
to solve a performance problem yourself, and therefore avoid sending your unit back 
for repair.

Fishing System Doesn’t Power Up

If your Fishing System doesn’t power up, use the installation guide that is included 
with your Fishing System to confirm specific details, making sure that:

•  the power cable is properly connected to the Fishing System control head,
•  the power cable is wired correctly, with red to positive battery terminal and 

black to negative terminal or ground,

•  the fuse is operational, and
•  the battery voltage of the power connector is at least

 

12 Volts.

Correct any known problems, including removing corrosion from the battery 
terminals or wiring, or actually replacing the battery if necessary.

Summary of Contents for MEGA 360 Fortrex



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands