manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Installation Manual

Share
Download
Humminbird MEGA 360 Fortrex Installation Manual Download Page 47

41

Specifications

Specifications

Operating Frequency ........................................................... 455 kHz / MEGA

 

Area of Coverage ........................................ 455 kHz / MEGA: (2) 90° @ -10 dB 

Power Output .................................................................. 500 Watts (RMS), 

4000 Watts (Peak to Peak) 

  

Power Requirement ................................................................ 10 to 18 VDC

 

Current Draw ...................................................................... .5 A maximum

 

Operating Temperature ....................................... -4°F to 158°F (-20°C to 70°C) 

Storage Temperature ....................................... -40°F to 158°F (-40°C to 70°C)

 

 

NOTE:

 Humminbird verifies maximum stated depth in saltwater conditions, but 

actual depth performance may vary due to transducer installation, water type, thermal 
layers, bottom composition and slope.

NOTE:

 Product specifications and features are subject to change without notice.

Summary of Contents for MEGA 360 Fortrex



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands