background image

FTK Operating Instruction Manual (Part 2)  

           

   

 

Version 2019/01  

11

6.5  Loading the Trailer

Make sure that the trailer is secured so  
 that it cannot roll away. 

Make sure that road traffic safety is not impaired  

 

when loading and unloading the trailer.

If necessary, use additional signalling devices,  

 

e.g. signs, barriers.

 

 

 Automatic lowering of the load 
platform!

 

 

 Crush hazard for hands / fingers caused by 
the front edge of the loading platform when 
loading.

Keep your hands away from the crush area.

Allow the the load platform to lower automatically.  

 

Never try to stop it.  

Wear 

.

  Moving load platform!

 

 

 You could fall if you step onto the load 
platform during the loading and unloading 
process and during automatic movement.

 Take particular care when stepping onto the load platform. 

Wear 

.

Interlocks opened

 Make sure that the interlocks are open on both sides 
before loading the trailer.

 The main load of the vehicle to the transported 
must be located at the front (drawbar) - so that the 
load platform of the trailer can lower automatically. 

Pay attention to the section: 6.1 Load distribution

 

 

WARNING

6.5.1  Loading the vehicle

Loading process (example)

 Drive onto the trailer carefully and not too quickly - the 
load platform can lower abruptly and can crash into the 
drawbar.

Drive up to the wheel stops (if present).

Use the winch to load a broken down vehicle. 

 Make sure that the position of the winch (3 adjusting 
positions) is set to the vehicle to be loaded - danger of 
collision. 
  - Handling the winch, see Operating instruction manual  
  "Car trailer“ (Part 1).

Never exceed the maximum permitted total  
 weight and vertical drawbar load of your trailer.

Observe the maximum permitted vertical drawbar 
load of your towing vehicle and trailer coupling. 

Lash the vehicle properly. 

 

Pay attention to section: 

6.2 Load Securing

6.5.2  Securing the load platform

1
2

3

Closing interlock 

Locking interlock

1.  Eyebolt
2.  Securing device
3.  Handle 

Lock the interlocks on both sides, one after the other.

Swing the eyebolt onto the locking hook.

Push the handle downwards.  

 

- The interlock engages and is interlocked.

Summary of Contents for FTK 4000 Series





















Reviews: