background image

 


 

 

 

 

Precautions 

 

To avoid electric shock do not open the front panel.  

 

Do not pull or hang on the machine.  

 

 Do not use the unit in a wet environment and away from standing water.  

 

Do not modify or dismantle the unit if not necessary.  

 

A suitably rated fused power supply is required 

 

Ensure the correct power supply is used. If power tolerance is over +/-10%, the unit may 

malfunction, causing fire or electric shock.  

 

The power must be turned off during maintenance.  

 

The drain tank and air filter must be installed for proper operation. Do not empty or 

replace after the power has been turned on. 

 

Remove from power source and close leakage circuit breaker if the unit is under 

abnormal status.  

 

Ensure the unit has a reliable ground connection. 

 

Do not install when connected to a power supply. 

 

The hand dryer must be installed by a qualified electrician. 

 

If the power cord is damaged, it must be replaced by the manufacturer, its service 

agent, or a qualified person.  

 

A residual current device (RCD) with a rated residual operating current not exceeding 

30mA is recommended.  

Environmental consideration 

 

Do not dispose of electrical waste with household waste. Please recycle in appropriate 

facilities. Check with your local authority or retailer for recycling advice.  

                   

WARNING:

 Misuse may cause injury.

 

Summary of Contents for Filter-Aire 2000














Reviews: