background image

 

11 
 

Cleaning Instructions 

It is important to clean the unit daily as part of routine restroom cleaning 

 

Clean with a soft cloth. It the unit is very dirty, use a soft cloth dampened with neutral cleaning 
agent, then wipe dry with a soft cloth. 

 

Remove dirt from the sensor (to prevent malfunction). 

 

 Note 

 

 

 

WARNING 

 

Before cleaning the unit ensure the power is off. 

 

DO NOT splash excessive water into the unit.  

 

CAUTION 

 

Wear gloves when cleaning 

 

The HEPA filter fiber takes effect when bacteria is trapped into the fibers of the filter.  

 

The HEPA filter will become ineffective if the filter is very dirty. 

 

Cleaning the Drain tank  

Daily  

 

It is necessary to regularly empty the drain tank to prevent water from exceeding the full level 

 

If the accumulated water is left in the drain tank, it may start to smell.  

 

Gently pull the drain tank out in a horizontal direction to avoid water 

splattering. 

 

   1. Open the cover and empty 

2. Wash and disinfect the inside of the drain tank 

3. Close the cover and return the drain tank to the unit 

Full level 

 

Only use neutral cleaning agents. 

 

Do not use thinner, (acidic or alkaline) toilet cleaners or nylon brushes 
(they may damage the surface) 

 

 Use alcohol* only to clean the hand drying area, but DO NOT use alcohol 
anywhere else on the unit. (*disinfectant alcohol below 83% 
concentration) 

 

If using chemical cloths please read instructions first. 

 

Disinfecting agents will damage the unit 

 

 

   

Summary of Contents for Filter-Aire 2000














Reviews: