background image

 

EN - ENGLISH – 01/2020 

 

Translation of original instructions

 

15

EN 

Reproduction is prohibited

 

tension. 

23. Keep your hands away from the drum and the roller fairlead whilst winding the cable around 

the drum. 

24. Secure the hook and the safety strap. 

25. Unplug the remote control and store it in a suitable, dry place. 

26. Clean and inspect the connections and mounting equipment for the next winching. 

 

09

 maintenance

 

 

9.1. Winch 

1.  Periodically check the tightness of the mounting bolts and electrical connections. Remove any 

dirt or corrosion and ensure the winch is always kept clean. 

2.  Do not attempt to disassemble the gearbox. Repairs must be carried out by the manufacturer 

or an approved repair centre. 

3.  The gearbox has been lubricated with high-temperature lithium grease and is factory-sealed. 

No internal lubrication is required. 

 

 

9.2. Cable 

If the cable is worn or begins to show signs that it might break, it must be replaced before using the 

winch. 

1.  Move the switch to the "DISENGAGE" position. 

2.  Pull out the full length of the cable. Take note of the manner in which the existing cable is 

attached to the drum. 

3.  Remove the old cable and attach a new cable to the drum. Insert the end of the new cable and 

tighten the M8 x 10 screw. 

4.  Ensure that the new cable is wound around the drum in the same direction as the old one. The 

cable must leave the drum from underneath the drum. 

5.  Move the switch to the “ENGAGE” position. 

6.  Wind the cable around the drum. The first five turns of steel cable (first 10 for synthetic cable) 

should be done carefully so that the cable is wound correctly. Next, the cable should be wound 
onto the drum with a load of at least 10% of the rated pulling force. 

 

WARNINGS

 

Any replacement cable must meet the same specifications  

as those recommended by the manufacturer. 

Summary of Contents for EB20000

























Reviews: