background image

13

D: \transformer winding deformation test result\test  print time. doc or test  print time. jpg.

The report could be WORD document or JPG photo, subject to the option selected in saving.

Part V Tester Maintenance

The section provides basic maintenance data. Please do not try to disintegrate, modify and repair

the transformer winding deformation tester.

5.1 Basic Maintenance

Regularly scrub surfaces of the tester and its accessories with a clean cloth.

Put the tester at a clean place with low humidity and protect it against entry of dirt and dust. Put the

tester into its packing case when not used and keep the packing case level.

5.2 Senior Maintenance

To be proceeded by professional technicians of the Company.

Part VI Ordering and Service

6.1

Damages of the tester as a result of product quality issue within three years since its delivery will be

repaired free of charge; for damages due to other reasons, the Company only charges repair cost.

6.2

We provide lifetime maintenance and technical services for the products.

6.3

Please contact us immediately upon discovery of any abnormality in the tester

.

We will provide the

most convenient solution for you. DO NOT disassemble the tester!

Summary of Contents for HZ-600C





















Reviews: