manualshive.com logo in svg

Huawei UPS2000-G-10KRTLV2, User Manual, Page: 99 / 158

Share
Download
Huawei UPS2000-G-10KRTLV2 User Manual Download Page 99

UPS2000-G-(3 kVA-20 kVA)-V2 
User Manual (Two Live Wires) 

7 Routine Maintenance 

 

Issue 07 (2019-12-19) 

Copyright © Huawei Technologies Co., Ltd. 

92 

 

Item 

Expected Result 

Measures 

Maintenance Interval 

Battery 
operating 
temperature 

1.

 

The ambient battery 
temperature is 
25±5°C. 

2.

 

The battery operating 
temperature is lower 
than battery 
tempe 20°C. 

3.

 

Battery charge and 
discharge conditions 
meet the requirements 
specified in the 
battery specifications. 

1.

 

Identify the cause of the 
abnormal battery 
operating temperature. 

2.

 

If the fault persists, 
contact Huawei technical 
support. 

Monthly 

Charge voltage 
of battery string 

 

Equalized voltage 
14.1 V x Number of 
batteries (tolerance 
±1%) 

 

Float voltage 13.5 V x 
Number of batteries 
(tolerance ±1%) 

1.

 

If the voltage drop 
between the battery string 
output terminals and the 
battery input terminals at 
the UPS side is greater 
than 1% of the battery 
string voltage, check 
whether the cable 
between the battery string 
and the UPS is 
excessively long, or the 
cable diameter is 
excessively small. 

2.

 

Check whether the 
equalized charging 
voltage and float charging 
voltage are correctly set 
for the UPS. 

3.

 

If the fault persists, 
contact Huawei technical 
support. 

Monthly 

Battery 
temperature 
sensor 
measurement 
accuracy 

The difference between 
the temperature measured 
by the temperature sensor 
and the temperature 
displayed on the LCD is 
less than 3°C. 

1.

 

Install the temperature 
sensor in the correct 
position. 

2.

 

Replace the battery 
temperature sensor. 

Quarterly 

Battery 
specifications 

The settings of battery 
management parameters 
meet the requirements in 
the user manual. 

Set parameters correctly. 

Quarterly 

Tightness of 
bolts on battery 
terminals 

The location of the signs 
marked on battery 
terminals indicating tight 
connections does not 
change. 

Take photos from multiple 
angles and contact Huawei 
technical support. 

Quarterly 

Cables between 

No cable deteriorates and 

Replace the faulty cable. 

Quarterly 

Summary of Contents for UPS2000-G-10KRTLV2































































































































































Reviews:

No comments