Huawei UPS2000-G-10KRTLV2 User Manual Download Page 121

Page: 121 / 158

UPS2000-G-(3 kVA-20 kVA)-V2
User Manual (Two Live Wires)

B LCD Menus and Parameters

Issue 07 (2019-12-19)

114

Main
Menu

Second-Level
Menu

Third-Level
Menu

Fourth-Level
Menu

Value Range

Preset Value

Converter mode

Enabled and
Disabled

Disabled

Bypass
(configurable
after the
inverter shuts
down)

Max. voltage

10%, 15%, 20%,
25%, and 30%

15%

Min. voltage

10%, 20%, 30%,
40%, 50%, and 60%

20%

Frequency range

±0.5 Hz, ±1 Hz, ±2
Hz, ±3 Hz, ±4 Hz,
±5 Hz, and ±6 Hz

±2 Hz

ECO
(configurable
after the
inverter shuts
down)

Max. voltage

5%, 6%, 7%, 8%,
9%, and 10%

10%

Min. voltage

5%, 6%, 7%, 8%,
9%, and 10%

10%

Frequency range

±0.5 Hz, ±1 Hz, ±2
Hz, and ±3 Hz

±2 Hz

Single UPS ECO

Enabled and
Disabled

Disabled

Power segment

Dis. time thres.
(configurable in
non-battery mode)

0–999 minutes

30 Min

Dis. volt. thres.
(configurable in
non-battery mode)

1.90–2.25 V/cell

2.00 V/cell

Power Segment
(configurable after
the inverter shuts
down)

Enabled and
Disabled

Disabled

Self-Load
(configurable
after the
inverter shuts
down)

Output power ratio

20%–100%

80%

Self-load mode

Enabled and
Disabled

Disabled

Others
(configurable
after the
inverter shuts
down)

Recovery delay
time

0–900 seconds

Max. BPS
transfers

1–3

Output transformer Enabled and

Disabled

Generator mode

Weak adaptability
mode, Balanced
mode, and Strong

Balanced mode

Summary of Contents for UPS2000-G-10KRTLV2































































































































































Search results

Summary of Contents for UPS2000-G-10KRTLV2

Reviews:

Huawei UPS2000-G-10KRTLV2, User Manual, Page: 121 / 158

Search results

Summary of Contents for UPS2000-G-10KRTLV2

Reviews: