Huawei U8650 Maintenance Manual Download Page 17

Page: 17 / 101

U8950 Maintenance Guide V1.0

5 Software Upgrade

2012-10-22

Huawei Proprietary and Confidential

Software Upgrade

5.1 Upgrade Preparation

Prepare the items listed in Table 5-1

Table 5-1

Items to be prepared before a software upgrade

Category

Item

Description

Upgrade
environment

Computer

Operating system: Windows 2000/Windows
XP

USB cable

BOM code: 02450768

Upgrade tool

NewMultiDownloadU

microSD card

The available space must be greater than 2
GB.

Battery

The power remaining must be more than two
bars.

Upgrade file

NewMultiDownloadU

This version is provided for reference only.
Please download the latest version when
upgrading the phone.

Upgrade
method

USB cable

Normal upgrade

Forcible upgrade

microSD card

Normal upgrade

Forcible upgrade

5.2 Hardware Connection

Connect the hardware in the way described in Figure 5-1.

Summary of Contents for U8650






































































































Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands

Huawei U8650, Maintenance Manual

Search results

Summary of Contents for U8650

Reviews:

Related manuals for U8650

Brands by name

Popular brands