Huawei U8185 Maintenance Manual Download Page 34

Page: 34 / 88

U8185
Maintenance Manual

9 Principles and Failure Analysis

Issue 1.0 (2012-03-23)

Huawei Proprietary and Confidential

Compared with constant voltage charging, pulsed charging performs better in charging
accuracy, charging speed, and efficiency. The software enables or disables the transistor to
charge the battery.

Troubleshooting Process

There are two types of common charging failures:



The phone does not respond when a charger is connected to it.



A charging indicator is displayed after a charger is connected to the phone but the phone
cannot be charged.

To troubleshoot charging failure, firstly check whether the battery connector is damaged.

Charging failure

Replace the charger

Is the charger

working properly?

Is USB connector

J901 poorly soldered?

Re-solder J901

Replace Q201

Is the battery in

good contact with

the battery connector

J902?

Repair or replace J902

Is the battery damaged?

End

Is voltage

available on C237?

Replace the battery

Summary of Contents for U8185

























































































Search results

Summary of Contents for U8185

Reviews:

Related manuals for U8185

Brands by name

Popular brands

Huawei U8185, Maintenance Manual

Search results

Summary of Contents for U8185

Reviews:

Related manuals for U8185

Brands by name

Popular brands