Huawei U8185 Maintenance Manual Download Page 73

Page: 73 / 88

U8185
Maintenance Manual

9 Principles and Failure Analysis

Issue 1.0 (2012-03-23)

Huawei Proprietary and Confidential

Analysis

The U8185 uses Qualcomm's WCN2243 FM/Bluetooth chip to receive and process FM
signals and realize the FM function. The stereo signals from the FM module are amplif ied by
the MSM7225A and then sent to the headset or speaker.

WCN2243 FM section's major features:



Broad frequency range (76–108 MHz); channel interval: 50 kHz



Transceiver integrated with an FM modem and a frequency synthesizer



Complying with RDS and RBDS



Manual and automatic tuning



Automatic gain control



Automatic frequency control



Adaptive noise reduction



Adjustment-free stereo decoder



Programmable de-emphasis



Standby mode



I2C, I2S, and PCM interfaces

The WCN2243 has the following modules integrated:

Summary of Contents for U8185

























































































Search results

Summary of Contents for U8185

Reviews:

Related manuals for U8185

Brands by name

Popular brands

Huawei U8185, Maintenance Manual

Search results

Summary of Contents for U8185

Reviews:

Related manuals for U8185

Brands by name

Popular brands