background image

4

 Configuration (Command Line Mode) 

U-SYS IAD101H/102H/104H Integrated Access Device 

Quick Start 

 

12 

Huawei Proprietary and Confidential        

Copyright © Huawei Technologies Co., Ltd. 

Issue 02 (2011-02-09) 

z

 

Run 

ipaddress static ip-address subnet-mask default-gateway

 to set a fixed IP 

address. 

z

 

Run 

ipaddress dhcp

 to obtain an IP address through DHCP. (A DHCP server is 

required.) 

z

 

Run 

pppoe username user-name password password

 to set the PPPoE user name 

and password, and then run 

ipaddress pppoe

 to obtain an IP address through 

PPPoE. (A PPPoE server is required, and the user name and password need to be 
set as the same as that on the PPPoE server.) 

You can run 

display ipaddress

 to view the IP address of the IAD. 

 

Changing the IP address may disconnect the Telnet connection. Then, you should establish 
the Telnet connection again with the new IP address. 

Step 3

 

Run the 

sip server index address ip-address domain user-domain-name

 command to 

set the SIP server and the user domain name. The IP address of the SIP server is 
191.168.10.20 and the user domain name is sichuan.chinamobile.com. 

TERMINAL(config)#

sip server 0 address 191.168.10.20 domain 

sichuan.chinamobile.com

 

If the prompt “Failure: Execution of command failed! Please undo the auto mode first” 
appears, run 

undo sip server auto

 to cancel the automatic mode of obtaining SIP 

server information, and set the IP address of the SIP server again. 

 

In IMS network, you can run the sip server auto command to make the IAD automatically 
obtain the IP address of P-CSCF (ie SIP server) through DHCP, or run the dns srv command 
to parse the IP addresses of SIP servers through SRV service on a DNS server. 

Step 4

 

Run the sip soft-parameter command to configure the SIP software parameters. 
The SIP software parameter configuration depends on the actual situation. The 
following configuration is only an example. 
Enter the advanced mode. 

TERMINAL(config)#

advanced

 

Use the user name for authentication. 

TERMINAL(advanced-config)#

sip soft-parameter auth-username name

 

Turn on the switch of the Tel URL. TelURL is a type of address in SIP protocol (ie 
+86-13612345678), which differs from SIPURL (ie [email protected]). 

TERMINAL(advanced-config)#

sip soft-parameter support-telurl on

 

Select new service control mode as local control to support forwarding new service 
invite mode. 

TERMINAL(advanced-config)#

sip soft-parameter new-service-mode local

 

Turn on the green call service switch. 

TERMINAL(advanced-config)#

sip soft-parameter support-in-band-dtmf on

 

Return to the global configuration mode. 

 

Summary of Contents for U-SYS IAD101H




















Reviews: