Huawei TaiShan 200 Series User Manual Download Page 69

Page: 69 / 132

Bind the new network cable in the same way as the existing network cables. You

can also remove all cable ties and bind all of the optical cables again if necessary.

----End

5.8.5 Connecting a USB Device

Step 1 Wear an ESD wrist strap. For details, see

5.3 ESD Protection

Step 2 Connect a USB device to a USB port on the server. See

Figure 5-21

Figure 5-21 Connecting a USB device

----End

5.8.6 Connecting a Serial Cable

The rear panel of the server provides a standard RJ45 serial port (three-pin serial

port), which works as the system serial port by default. You can set it as the iBMC

serial port using the iBMC CLI.

The serial port can be used as:

●

System serial port to monitor the OS status

●

iBMC serial port for debugging and fault locating

Procedure

Step 1 Wear an ESD wrist strap. For details, see

5.3 ESD Protection

Step 2 Plug the connector into the serial port. See

Figure 5-22

TaiShan 200 Server

User Guide (Model 2280)

5 Install and Configure

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands