Huawei SmartACBox Quick Manual Download Page 10 | Manualshive

Page: 10 / 30

background image

9

Enclosure Dimensions

Mounting Bracket Dimensions

2

Installing the SmartACBox

Preparing for the Installation

2.1

Installation Space

Expansion Bolt

(1) Expansion sleeve (2) Flat washer

(3) Spring washer

(4) M12x60 bolt

M12x60 expansion bolts and M12x40 bolt
assemblies are delivered with the
SmartACBox. M12x40 bolt assemblies are
used for support-mounting and pole-mounting
the SmartACBox. Such a bolt assembly
consists of a flat washer, a spring washer, and
an M12x40 bolt.

Installing the Mounting Bracket

2.2

The mounting bracket has four groups of tapped holes, each group containing four tapped holes.
Mark any hole in each group based on site requirements and mark four holes in total. Two round
holes are preferred.

Wall-mounted Installation

Avoid drilling holes in the water pipes and cables buried in the wall.

«
...
8
9
10
11
12
...
»

Summary of Contents for SmartACBox































Reviews:

No comments

Related manuals for SmartACBox

Relion 670 series

Brand: ABB Pages: 66

Brand: Sagola Pages: 20

Inocoat Inocenter

Brand: Sames Pages: 58

Perma-Tork HB6-1

Brand: Magpowr Pages: 4

Brand: CNC Pages: 21

Precision CPU-H Series

Brand: Harmonic Drive Pages: 12

F120-H824.11 S11RW2V

Brand: Jäger Pages: 52

Brand: lancer Pages: 4

Brand: BIRD Pages: 24

Brand: MAKSIWA Pages: 80

Brand: ROVEMA Pages: 157

Sibo SZB SE 33U

Brand: Elektro-Automatik Pages: 16

Brand: Rollsizer Pages: 28

Brand: Beckhoff Pages: 22

Brand: RINGSPANN Pages: 16

Brand: Kval Pages: 118

Brand: Crane Pages: 3

Brand: Moeller Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands