Huawei Quidway S5000 Series Routine Maintenance Download Page 55

Page: 55 / 68

Parameter

Description

Associate Disk

The associated status between the disk and the other disks. The location
of the associated disk will be indicated if there is an associtation.

If the logical status is

Used Hot-Spare Disk

, it indicates the position

of the faulty disk that the hot-spare disk reconstructs data from or
copies data back to.

If the logical status is

Fault

: indicates the position of the hot-spare

disk that the faulty disk is associated with.

If the logical status is

Used Hot-Spare Disk

and

Fault

: indicates that

this parameter is valid.

RAID Group

This parameter indicates the RAID group where the disk belongs to.
When the value of the

Logical Type

Member Disk

, the parameter is

valid.

Logical Status

The logical status of a disk is shown as follows:

Normal

: indicates that the disk can be used normally.

Fault

: indicates that the hard disk is faulty.

Reconstructing

: indicates that the system is reconstructing the data

from the faulty disk to the hot-spare disk.

Reconstruction Complete

: indicates that all the data on the faulty

disk is reconstructed to he hot-spare disk.

Performing Copyback

: indicates that when the faulty disk is restored

or is replaced by a normal disk, the system copies the data from the
hot-spare disk back to the restored faulty disk or the normal disk.

Free

: indicates that the free hot-spare disk is not in use.

In Use

: indicates that the hot-spare disk is in use.

Capacity (GB)

This parameter indicates the total capacity of the system disk, and the
unit is GB.

Physical Status

The physical status of a disk is shown as follows:

Normal

: indicates that the disk can be used normally.

Fault

: indicates that the disk is faulty and cannot be used normally.

Offline

: indicates that the disk cannot be accessed, or the disk does

not exist.

The hard disk will fail

: Indicates that the system detects the disk to

be faulty, and the disk needs to be replaced with a new disk.

Primary Access
Path

This parameter indicates the data link status between the primary
controller and the disk. The status can be

Normal

Fault

Secondary Access
Path

This parameter indicates the data link status between the secondary
controller and the disk. The status can be

Normal

Fault

Temperature (°C)

This parameter indicates the temperature of a hard disk.

Rotation Speed
(RPM)

This parameter indicates the rotational speed of the disk.

OceanStor S5000 Series Storage System
Routine Maintenance

5 Routine Maintenance Guide of the OSM

Issue 01 (2010-04-20)

Huawei Proprietary and Confidential

5-11

Summary of Contents for Quidway S5000 Series





































































Search results

Summary of Contents for Quidway S5000 Series

Reviews:

Related manuals for Quidway S5000 Series

Brands by name

Popular brands

Huawei Quidway S5000 Series, Routine Maintenance

Search results

Summary of Contents for Quidway S5000 Series

Reviews:

Related manuals for Quidway S5000 Series

Brands by name

Popular brands