manualshive.com logo in svg

Huawei Quidway S3900 Series, Installation Manual

Share
Download
Huawei Quidway S3900 Series Installation Manual Download Page 47

Installation Manual 
Quidway S3900 Series Ethernet Switches 

Chapter 1  Product Overview

 

Huawei Technologies Proprietary 

1-31 

LED 

Mark 

Color 

Indicates 

ON 

A 1000 Mbps link is present. 

Green

Flash 

Data is being received/sent on 
the port 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Speed 

OFF 

No link is present. 

ON 

The port is operating in full 
duplex mode 

Green

Flash 

Data is being received/sent on 
the port 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Duplex 

OFF 

No link is present. 

Flashing green 
(3 Hz) 

The port fails POST. 

1000Bas
e SFP 
port LED

 

PoE 

OFF –– 

ON 

The port is connected, and the 
device is in an IRF loop fabric. 

Green

Flash 

Data is being received/sent on 
the port 

ON 

The port is connected, and the 
device is in an IRF chain fabric.

Yellow

Flash 

Data is being received/sent on 
the port 

Flashing green 
(3 Hz) 

Fabricing fault occurs. 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Speed 

OFF 

The port is not connected. 

ON 

The port is in full duplex mode 
and is fabriced. 

Green

Flash 

Data is being received/sent on 
the port. 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Duplex 

OFF 

The port is not connected. 

OFF 

No data is being received/sent

1000Bas
e SFP 
Fabric 
port LED

 

 
PoE 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Summary of Contents for Quidway S3900 Series
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands