manualshive.com logo in svg

Huawei Quidway S3900 Series, Installation Manual

Share
Download
Huawei Quidway S3900 Series Installation Manual Download Page 38

Installation Manual 
Quidway S3900 Series Ethernet Switches 

Chapter 1  Product Overview

 

Huawei Technologies Proprietary 

1-22 

LED 

Mark 

Color 

Indicates 

POST 
running 

PWR  flashes 
green 

The POST test ID (in the range 
1 to 9). 

PWR  flashes 
yellow 

POST 
failed 

PWR stays red 

POST test ID of the failed test.

Software 
loading 

PWR  flashes 
green 

A bar rotates clockwise around 
the display. 

Fan 
failure 

PWR stays red 

“F”, meaning the FAN fails. 

7- 
segment 
digitron 
display 

Unit 

Unit id 

Button released 

UNIT ID in the fabric; and for a 
standalone unit, “1” 

ON 

A 100 Mbps link is present. 

Green

Flash 

Data is being received/sent on 
the port 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Speed 

OFF 

No link is present. 

ON 

The port is operating in full 
duplex mode 

Green

Flash 

Data is being received/sent on 
the port 

Flashing yellow 
(3 Hz) 

The port fails POST. 

100Base 
SFP port 
LED 

 

Duplex 

OFF 

No data is being received/sent 
on the port. 

Summary of Contents for Quidway S3900 Series
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands