Huawei Quidway S3900 Series Installation Manual Download Page 42

Page: 42 / 95

Installation Manual
Quidway S3900 Series Ethernet Switches

Chapter 1 Product Overview

Huawei Technologies Proprietary

1-26

Table 1-12

100Base SFP modules and cable specifications

SFP module

Central

wavelength

Conne

ctor

Fiber

specifications

Transmission

segment

100Base-FX-MM-
SFP

62.5µm/125µm
multi-mode
fiber

2 km (1.24 mi)

100Base-FX-SM-
SFP

9µm/125µm
single mode
fiber

15 km (9.32 mi)

100Base-FX-SM-
LR-SFP

1310 nm

9µm/125µm
single mode
fiber

40 km (24.86 mi)

100Base-FX-SM-
VR-SFP

1550 nm

9µm/125µm
single mode
fiber

80 km (49.71 mi)

IV. Attributes to the 1000 Mbps SFP ports

Depending on your needs, the S3928F-EI can provide two 1000 Mbps SFP ports,
which are numbered 25 and 26, and can be optical or electrical.

SFP modules allow for great flexibility because they are hot swappable and user
configurable.

For available SFP modules, see Table 1-6.

Note:

The available 1000 Mbps SFP modules are subject to changes. For information on the
latest module options, contact your sales agent.

V. Attributes of the 10/100/1000Base-T Ethernet ports

The S3928F-EI can provide two 10/100/1000Base-T Ethernet ports (numbered 27 and
28) on its front panel. See Table 1-8 for port attributes.

VI. Console port

The S3928F-EI provides one EIA/TIA-232 compliant Console port for local or remote
switch configuration. For its attributes, see Table 1-4.

1.7.2 Rear Panel

The S3928F-EI has an AC-input power socket, a DC power socket and a grounding
screw on its rear panel, as shown in Figure 1-12:

Summary of Contents for Quidway S3900 Series
































































































Search results

Summary of Contents for Quidway S3900 Series

Reviews:

Brands by name

Popular brands

Huawei Quidway S3900 Series, Installation Manual

Search results

Summary of Contents for Quidway S3900 Series

Reviews:

Brands by name

Popular brands