background image

Installation Reference 

64/65 >>

 

• Before powering on the equipment, ensure that: 
  - The RTN 900 has been powered on. 

  - The GE cable used for providing power over Ethernet has been installed. 
• Power on the equipment within 24 hours of unpacking. 
• During maintenance, the power-off time of the equipment must not be longer than 24 hours. 

Caution 

2. Check the system indicator on the RTN 310. 

NOTE 

In normal cases: 
•The power over Ethernet indicator of the EG4P board on the RTN 900 is steady green, and the L/A3 
indicator is steady green or blinks yellow. For the indicator status description, see the 

OptiX RTN 900 

IDU Hardware Description

•The system indicator on the RTN 310 is on. For the indicator status description, see the 

Product 

Description

System 
indicator 

1. Use the Web LCT to enable the PoE function for the interconnected port on the EG4P board of the RTN 900. 

 a. In the NE Explorer, select the desired NE from the Object Tree and choose 

Configuration

 > 

Interface 

Management

 > 

Ethernet Interface

 from the Function Tree. 

 b. Click the 

Advanced Attributes

 tab. 

 c. Set 

POE

 to 

Enabled

 for the port that provides power over Ethernet to the RTN 310. 

 d. Click 

Apply

RTN 900 

RTN 310 

Web LCT 

Power over 
Ethernet indicator 

L/A3 indicator 

Powering On the RTN 310 Working with the RTN 900 

Powering On the RTN 310 Supplied by an Indoor PI 

• Before powering on the equipment, ensure that: 
  - The GE cable used for providing power over Ethernet 
and the PI power cable have been installed. 

  - The indoor PI works in PSE-PD mode. If the indoor PI is 
powered on and works in FORCE mode, disconnect the 
input power cable from the PI and push the power output 
switch of the PI to the PSE-PD side. 
• Power on the equipment within 24 hours of unpacking. 
• During maintenance, the power-off time of the equipment 
must not be longer than 24 hours. 

Caution 

NOTE 

In normal cases, the DC IN and P&E OUT indicators are 
steady green. For the indicator status description, see 
the 

Product Description

Switch on the power supply device connected to the PI. 

Check the system indicator on the RTN 310. 

System indicator 

1

2

NOTE 

In normal cases, the system indicator is on. For 
the indicator status description, see the 

Product Description

P&E ports (3/P1 and 4/P2) on the EG4P board 

When a P&E port on the OptiX RTN 900 is connected to a 
device other than OptiX RTN 300, the PoE function must be 
disabled. Otherwise, the peer device may be damaged. 
 

P&E port 

Powering On the RTN 310 Supplied by an Outdoor PI 

Check the system indicator on the RTN 310. 

System indicator 

2

NOTE 

In normal cases, the system indicator is on. 
For the indicator status description, see the 

Product Description

PSE-PD 

Power Output Mode 

Before powering on the equipment, ensure that: 
•The P&E cable and the PI power cable are installed. 
•DIP switches are set correctly, and the DIP switch for setting the 
PoE mode for the used P&E port is turned to the PSE-PD side. 
After setting the DIP switches, switch off the power supply. After 
waiting for 6 seconds, switch on the power supply again. 
• Power on the equipment within 24 hours of unpacking. 
• During maintenance, the power-off time of the equipment 
cannot be longer than 24 hours. 

Caution 

NOTE 

In normal conditions, POWER and P&E OUT indicators are on 
(green). For a description of indicator states, see the PI 
installation guide. 

1

POWER 

P&E OUT 

Switch on the power supply device connected to the PI. 

Summary of Contents for OptiX RTN 310



































Reviews: