Huawei IVS1800 User Manual Download Page 12

Page: 12 / 63

Name

Type

Function

Power button

Powers on or off the service software.
● After the power switch of the device is turned on,

the device automatically enters the running state.

You do not need to press the power button.

● When the power switch is turned on, you can

press the power button and hold it down for 10s

to enter the standby mode. If you press the power

button again, the device enters the running state.
When the device is in standby mode, the power

button indicator is steady blue. When the device

is running, the power button indicator is off.

Reset button

● Hold down this button for 1s to reset the system.
● Hold down this button for 10s to restore the

device to factory defaults.

Power cable

port

Connects the power supply.

Power switch

Powers on or off the device.

Table 2-4 Indicator description

Name

Status Description

Network port ACT indicator

● Off: No data is being transmitted.
● Blinking: Data is being transmitted.

Network port LINK indicator

● Steady on: The network port is

connected properly.

● Off: The network port is not

connected.

Power-on/off status indicator

● Steady on: The service software is

running.

● Off: The service software is not

started.

IVS1800 Video Management System

User Manual

2 IVS1800 Overview

Issue 02 (2021-01-27)

Summary of Contents for IVS1800
































































Search results

Summary of Contents for IVS1800

Reviews:

Related manuals for IVS1800

Brands by name

Popular brands

Huawei IVS1800, User Manual

Search results

Summary of Contents for IVS1800

Reviews:

Related manuals for IVS1800

Brands by name

Popular brands