Huawei EM820W Page 40 Hardware Manual Download

Page: 40 / 49

HUAWEI EM820W HSPA+ PC Embedded Module
Hardware Guide

Electrical and Reliability Features

Issue 01 (2010-12-09)

Huawei Proprietary and Confidential

Description

Test Value

Units

PCL

Configuration

362

4 Up/1 Down

128

1 Up/1 Down

165

2 Up/1 Down

210

mA 10

4 Up/1 Down

194

1 Up/1 Down

257

2 Up/1 Down

341

mA 2

4 Up/1 Down

142

1 Up/1 Down

177

2 Up/1 Down

EDGE1900

218

mA 10

4 Up/1 Down

Table 5-6

DC power consumption(Idle and Suspend)

Idle

Suspend

Scenario

Offline
Enabled

Offline
Disabled

Offline
Enabled

Offline
Disabled

Unit

WCDMA 2100MHz
DRX = 8 (2.56 s)

66.3 72.7 4.1 5.8 mA

GSM 900MHz
MFRM = 5 (1.18 s)

70.6 73.1 4.1 7.8 mA

In idle mode, the module is registered to the network, USB bus is active, and no voice or
data call connection is ongoing.

The above values are the average of some test samples.

5.6 Reliability Features

Table 5-7 lists the test conditions and results of the mechanical reliability of the
EM820W module.

Summary of Contents for EM820W


















































Search results

Summary of Contents for EM820W

Reviews:

Related manuals for EM820W

Brands by name

Popular brands

Huawei EM820W, Hardware Manual

Search results

Summary of Contents for EM820W

Reviews:

Related manuals for EM820W

Brands by name

Popular brands