background image

 

HUAWEI EM820W HSPA+ PC Embedded Module 
Hardware Guide   

RF Specifications

 

Issue 01 (2010-12-09) 

Huawei Proprietary and Confidential 

Copyright © Huawei Technologies Co., Ltd. 

23

 

4.4.2 Interference 

Besides the antenna performance, the interference on the user board also affects the 
radio performance (especially the TIS) of the module. To guarantee high performance 
of the module, the interference sources on the user board must be properly controlled. 

On the user board, there are various interference sources, such as the LCD, CPU, 
audio circuits, and power supply. All the interference sources emit interference 
signals that affect the normal operation of the module. For example, the module 
sensitivity can be decreased due to interference signals. Therefore, during the design, 
you need to consider how to lessen the effects of interference sources on the module. 
To lessen the effects of interference sources on the module, you can use an LCD 
with optimized performance, shield the LCD interference signals, shield the signal 
cable of the board, or design filter circuits. 

Huawei is capable of making technical suggestions on radio performance 
improvement of the module. 

4.4.3 GSM/WCDMA Antenna Requirements 

The antenna for EM820W must fulfill the following requirements: 

Table 4-5 

GSM/WCDMA antenna requirements 

GSM/WCDMA Antenna Requirements   

Frequency range 

Depending on the frequency band(s) provided by the 
network operator, the customer must use the most 
suitable antenna for that/those band(s)   

Bandwidth 

70 MHz in GSM850 
80 MHz in GSM900 
170 MHz in DCS   
140 MHz PCS   
70 MHZ in WCDMA850   
80 MHz in WCDMA900   
140 MHz in WCDMA1900   
250 MHz in WCDMA2100 band 

Gain   

Gain < 3dBi   

Impedance 50 

Ohm 

 

Input power 

> 33dBm(2 W) peak power in GSM   
> 24dBm Average power in WCDMA   

VSWR absolute max 

<= 10:1   

VSWR recommended 

<= 2:1   

 

Furthermore, if the device is developed for US and/or Canada market, it must comply 
with the FCC and/or IC approval requirements:   

Summary of Contents for EM820W


















































Reviews: