manualshive.com logo in svg

Huawei EM820W, Hardware Manual

Share
Download
Huawei EM820W Hardware Manual Download Page 31

 

HUAWEI EM820W HSPA+ PC Embedded Module 
Hardware Guide   

RF Specifications

 

Issue 01 (2010-12-09) 

Huawei Proprietary and Confidential 

Copyright © Huawei Technologies Co., Ltd. 

24

 

This device is to be used only for mobile and fixed application. The antenna(s) used 
for this transmitter must be installed to provide a separation distance of at least 20 
cm from all persons and must not be co-located or operating in conjunction with any 
other antenna or transmitter. End-Users must be provided with transmitter operation 
conditions for satisfying RF exposure compliance. OEM integrators must ensure that 
the end user has no manual

 

instructions to remove or install the UC864-E/G/WD 

/WDU module. Antennas used for this OEM module must not exceed 3dBi gain for 
mobile and fixed operating configurations. 

4.4.4 Radio Test Environment 

The antenna efficiency, antenna gain, radiation pattern, total radiated power (TRP), 
and TIS can be tested in a microwave testing chamber. 

Huawei has a complete set of OTA test environment (SATIMO microwave testing 
chambers and ETS microwave testing chambers). The testing chambers are certified 
by professional organizations and are applicable to testing at frequencies ranging 
from 380 MHz to 6 GHz. The test items are described as follows: 

Passive Tests 

z

 

Antenna efficiency 

z

 

Gain 

z

 

Pattern shape 

z

 

Envelope correlation coefficient 

Active Tests 

z

 

TRP:

 GSM, WCDMA, CDMA, TD-SCDMA, and LTE systems 

z

 

TIS:

 GSM, WCDMA, CDMA, TD-SCDMA, and LTE systems 

Figure 4-1 shows the SATIMO microwave testing chamber. 

Summary of Contents for EM820W


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands