Huawei Airbridge cBTS3612 Maintenance Manual Download Page 73

Page: 73 / 101

On-site Maintenance Manual
Airbridge cBTS3612 CDMA Base Station

Chapter 4 Component

Replacement

4-8

4.2

Exceptional Procedure of Replacement

Note:

1. This procedure is based on the “4.1.1 Board Replacement”.

2. As we are going to focus on the parts different from the common replacement
procedure, be sure to get familiar with the “4.1.1 Board Replacement” first. Follow
the procedure exactly throughout the replacement process.

4.2.1 BTS E1 Surge Protector (BESP)

The physical structure and installation position of BESP are

rather different from those of the boards in the baseband subrack,

therefore, while basically observing the “4.1.1 Board Replacement”

(some processes, such as the board removal and installation, are not

applicable to BESP and thus, can be handled flexibly), we should

also pay attention to the following:

The influence on the service

Replacing a BESP may interrupt all the services transmitted

through it.

II.

Cut off and resume the power supply

Before replacing the board, we should toggle off all the switches

in the BTS switch box one by one (first the switch for the RF module,

then the baseband subrack, then the fan and then the power

Summary of Contents for Airbridge cBTS3612






































































































Search results

Summary of Contents for Airbridge cBTS3612

Reviews:

Related manuals for Airbridge cBTS3612

Brands by name

Popular brands

Huawei Airbridge cBTS3612, Maintenance Manual

Search results

Summary of Contents for Airbridge cBTS3612

Reviews:

Related manuals for Airbridge cBTS3612

Brands by name

Popular brands