Huawei Airbridge cBTS3612 Maintenance Manual Download Page 53

Page: 53 / 101

On-site Maintenance Manual
Airbridge cBTS3612 CDMA Base Station

Chapter 3 Component Failure

Handling

3-16

3.7

BTS Transceiver Module (BTRM)

3.7.1 Fault Description

Receiving channel over-excited

II.

Software phase -lock unlocked

III.

Abnormal forward link power

IV.

Alarm on abnormal reverse signal strength

RS485 link failure alarm

VI.

Other faults in the BTRM

Other faults in the BTRM include: transmitting channel clock

unlocked, hardware phase-lock unlocked, abnormal I

value and the

digital down frequency-converter failure.

VII.

BTS RF Fan Module failure

RF fan module failures include:

the BTS Fan Monitor Module is unable to read the temperature

sensor;

the fan is not running properly;

the BTS Fan Monitor Module generates a high-temperature alarm;

and the fan monitoring board is unable to control the fan speed.

Summary of Contents for Airbridge cBTS3612






































































































Search results

Summary of Contents for Airbridge cBTS3612

Reviews:

Related manuals for Airbridge cBTS3612

Brands by name

Popular brands

Huawei Airbridge cBTS3612, Maintenance Manual

Search results

Summary of Contents for Airbridge cBTS3612

Reviews:

Related manuals for Airbridge cBTS3612

Brands by name

Popular brands