Huawei Airbridge cBTS3612 Maintenance Manual Download Page 86

Page: 86 / 101

On-site Maintenance Manual
Airbridge cBTS3612 CDMA Base Station

Chapter 5 Component

Indicators

5-3

5.3

BTS Channel Process Module (BCPM)

For details about the BCPM indicators, please see Table 5-3

Table 5-3

Descriptions of BCPM indicators

Indicator

Color

Meaning

Description

Normal Status

RUN

Green

Status

Indicator

Flashing quickly (at 4Hz): The

BCPM is undergoing the

power-on initialization or the

software download.

Flashing slowly (at 0.5Hz): The

BCPM is running properly.

Other: The BCPM is not

working properly.

Flashing slowly

ALM

Red

Alarm

indicator

Flashing quickly (at 4Hz):

Critical alarm

Flashing slowly (at 0.5Hz):

Major alarm

Flashing slowly (at 0.25Hz):

Minor alarm

Off: No alarm

Off

ACT

Green

Operation

indicator

On: The BCPM is working

properly.

Flashing quickly (at 4Hz): Cell

Bus failure.

Flashing slowly (at 0. 5Hz):

Main control signaling link

alarm.

Flashing slowly (at 0.25Hz):

CSM5000 alarm.

Summary of Contents for Airbridge cBTS3612






































































































Search results

Summary of Contents for Airbridge cBTS3612

Reviews:

Related manuals for Airbridge cBTS3612

Brands by name

Popular brands

Huawei Airbridge cBTS3612, Maintenance Manual

Search results

Summary of Contents for Airbridge cBTS3612

Reviews:

Related manuals for Airbridge cBTS3612

Brands by name

Popular brands